Metrohm 7A501C Safety Insulation Tester
Metrohm 7A501C Safety Insulation Tester
Trusted by Professionals
Search:
  
Martindale Electric on Facebook Martindale Electric on Twitter Martindale Electric on Linked In Martindale on Google+ Martindale on YouTube

Metrohm 7A501C Safety Insulation Tester

Metrohm 7A501C Safety Insulation Tester
general image
Metrohm 7A501C Safety Insulation Tester
general image
Martindale Part No: MET7A501C

The Metrohm 7A501C safety insulation tester, originally designed for use in hazardous areas - such as mines and petrol sites. With the introduction of the new ATEX regulations, the item no longer meets requirements for intrinsically safe products, however this product has been in active service for 45 years in hazardous areas.

There are no other testers of this kind on the market, that we know of, which fully meet ATEX requirements, therefore the use of this tester should be decided upon by a suitably qualified and knowledgeable person. Whilst this tester does not qualify for ATEX approval, safety officers should evaluate the risks of failing to perform adequate electrical safety testing. Below are the details of the availability and compliance statements issued after the changeover from Intrinsically Safe to ATEX regulations. As such this product is only available for sale where the intended use is outside the EU.

The 7A501C is supplied with test leads, carry case, battery and safety tool to remove battery cover.

Metrohm 7A501C Compliance Statement - July 2003
In 1965, The Factories Inspectorate in the U.K. issued to Edgcumbe Instruments Intrinsically Safe Certificate number 2148, for the Metrohm 7A501C. This approved the instrument as suitable for use as an insulation tester in gases and vapours classified as 2a and 2c in Table I of BS 1259:1958. “Intrinsically Safe” was permitted to be applied to the instrument, as defined in BS 1259:1958.

In the last 38 years there have been no accidents reported attributable to the use of a 7A501C in explosive atmospheres.

Martindale Electric Co Ltd acquired the product and all associated rights in 2003.

In order to preserve the relevance of the certification, Martindale Electric adheres to the same parts listings and construction techniques as those used by Edgcumbe in manufacture of the 7A501C.

Copies of I.S. Certificate 2148 are available upon customer request.

It should be noted that B.S.1259 was superseded by B.S.5501-9:1982 and more recently by both BS EN 50014:1998 and BS EN 50020:2002.

In addition, the ATEX 94 Directive now applies in certain countries to equipment used in explosive atmospheres and places a different interpretation on the term “Intrinsically Safe”.

The 7A501C will not comply with the ATEX 94 Directive and is marked to this effect. We now supply the 7A501C as a Safety Insulation Tester.

Ongoing use of existing 7A501C testers in explosive atmospheres is permitted up to July 2006, but new purchases should be ATEX 94 compliant, if they are to be used where ATEX 94 applies.

To our knowledge, there is no ATEX 94 compliant insulation tester available.

In an environment where ATEX 94 applies, the purchase of a new 7A501C to carry out essential electrical safety tests should be subject to a risk analysis by the site safety officer.

Service replacement of key modules in existing instruments remains permitted.

For environments where the ATEX 94 Directive does not apply, the original certification and “Intrinsically Safe” marking remains valid.

Metrohm 7A501C Availability Statement - April 2006

A detailed technical review of the Metrohm 7A501C has resulted in the decision to withdraw it from sale in the EU.

However, non compliance with ATEX 94 prevents CE marking, as there is a relevant directive with which the product does not comply.

Accordingly, the product is now only available for sale where the intended place of use is outside the EU.


Insulation Range
  • 0 - 50MΩ

Test Voltage

  • 500V DC +/- 10% across 1MΩ

Short Circuit Current

  • <2mA

Accuracy

  • +/- 1.6mm of scale arc length

Continuity

  • Range: 0 - 50Ω
  • Test Voltage: nominal 200mV
  • Short Circuit Current: <26mA
  • Accuracy: +/- 1.6mm of scale arc length

General Specification

  • Complies With: BS1259
  • Supply: 1.5V AA IEC batteries
  • Housing: Shatterproof ABS case
  • Dimensions: 32 x 82 x 60mm
  • Weight: 600g approx
  • Supplied with case, test leads (DFK0113), safety tool to remove battery cover & instruction manual
Print    Bookmark    Manual     Datasheet   
general image
general image
Metrohm - a Martindale Brand
Drummond - a Martindale Brand
Luckins Logo - Martindale is listed in Luckins Live Martindale Electric Co Ltd, Metrohm House, Imperial Park, Imperial Way, Watford, Hertfordshire, WD24 4PP
Company Registration No: 3387451. © Martindale Electric Co Ltd 1997 - 2017, all rights reserved.
T: +44 (0) 1923 441 717   F: +44 (0) 1923 446 900   E: sales@martindale-electric.co.uk
E. & O.E. Privacy Notice | Terms & Conditions | Contact Us